Panasonic PT-DZ16K Laser Lamp free 16000 Lumens Full HD Projector

SKU: AVPR208

3-chip DLP, 16000 lumens, FULL HD 
   120Hz high frame rate for superb and sharp motion pictures 
   Compact design, light weight and low noise level (as low as 46db) 
   Quad-lamp redundancy for failsafe operation 
   Fully featured for single or multi-mapping installations

Brightness	16,000 lumens (four lamp)
Resolution	1,920 x 1,080 pixels (Input signals that exceed this resolution will be converted to 1,920 x 1,080 pixels.)
Lamp	432 W UHM lamps (x 4) (four lamp system)
Power supply	200 - 240 V AC, 12 A, 50/60 Hz (3-wire single-phase)
Power consumption	2,060 W (2,100 VA) (0.3 W with STANDBY MODE set to ECO. 9 W with STANDBY MODE set to NORMAL.), max. 7,031 BTU (without light output: 6,758 BTU )
DLP™ chip \| Panel size	24.1 mm (0.95 inches) diagonal (16:9 aspect ratio)
DLP™ chip \| Display method	DLP™ chip x 3 (R, G, B), DLP™ projection system
DLP™ chip \| Pixels	2,073,600 (1,920 x 1,080) x 3, total of 6,220,800 pixels
LENS	Optional powered zoom/focus lenses
Screen size	1.78-25.4 m (70-1,000 inches) (1.78-15.24 m (70-600 inches) with the ET-D75LE8 tele), (1.78-7.62 m(70 - 300 inches) with the ET-D75LE5, 16:9 aspect ratio
Center-to-corner uniformity	90%
Contrast	10,000:1 (full on/full off, in dynamic iris 3 mode)
Scanning frequency \| SDI	3G-SDI signal (YPBPR 4:2:2 10-bit): SMPTE ST 424 compliant: 1080/50p, 1080/60p, (RGB4:4:4 12bit/10bit): SMPTE ST 424 compliant: 1080/50i, 1080/60i, 1080/25p, 1080/24p 1080/24sF, 1080/30p Single-link HD-SDI signal (YPBPR 4:2:2 10-bit): SMPTE ST 292 compliant: 720/50p, 720/60p, 1035/60i, 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p SD-SDI signal (YCBCR 4:2:2 10-bit): SMPTE ST 259 compliant: 480i, 576i
Scanning frequency \| HDMI/DVI-D/DIGITAL LINK/RGB	Horizontal: 15-100 kHz, vertical: 24-120 Hz, dot clock: 162MHz or less HDMI/DVI-D : 25 MHz-162MHz)
Scanning frequency \| YPBPR (YCBCR)	480i (525i): fH 15.73 kHz; fV 59.94 Hz, 576i (625i): fH 15.63 kHz; fV 50 Hz, 480p (525p): fH 31.47 kHz; fV 59.94 Hz, 576p (625p): fH 31.25 kHz; fV 50 Hz, 720 (750)/60p: fH 45.00 kHz; fV 60 Hz, 720 (750)/50p: fH 37.50 kHz; fV 50 Hz, 1035/60i: fH 33.75 kHz; fV 60 Hz, 1080 (1125)/60i: fH 33.75 kHz; fV 60 Hz, 1080 (1125)/50i: fH 28.13 kHz; fV 50 Hz, 1080/25p: fH 28.13 kHz; fV 25 Hz, 1080/24p: fH 27.00 kHz; fV 24 Hz, 1080/24sF: fH 27.00 kHz; fV 48 Hz, 1080/30p: fH 33.75 kHz; fV 30 Hz, 1080/60p: fH 67.50 kHz; fV 60 Hz, 1080/50p: fH 56.25 kHz; fV 50 Hz
Scanning frequency \| Video/Y/C	fH: 15.73 kHz, fV: 59.94 Hz [NTSC/NTSC4.43/PAL-M/PAL60] fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]
Optical axis shift \| Vertical	±60% (±50% with the ET-D75LE6, +75-+88% with the ET-D75LE90) from center of screen, powered
Optical axis shift \| Horizontal	±20% (±15% with the ET-D75LE6, -12-+14% with the ET-D75LE90) from center of screen, powered NOTE: Optical axis shift function cannot be operated when used with the ET-D75LE50.
Keystone correction range	Vertical : ±40° (±22° with the ET-D75LE50, ±28° with the ET-D75LE6, +5° with the ET-D75LE90), horizontal: ±15°
Installation	Ceiling/・or, front/rear
Terminals \| SDI IN	BNC x 1, 3G-SDI signal: SMPTE ST 424 compliant Dual-link HD-SDI signal: SMPTE ST 292 compliant SD-SDI signal: SMPTE ST 259 compliant
Terminals \| HDMI IN	HDMI 19-pin x 1, Deep Color, compatible with HDCP
Terminals \| DVI-D IN	DVI-D 24-pin x 1, DVI 1.0 compliant, HDCP compatible, for single l ink only
Terminals \| DIGITAL LINK/LAN	RJ-45 Network connection / digital link connection (video/network/serial control) compliant with PJLink,100base-tx, Art-Net compatible Deep Color, compatible with HDCP
Terminals \| RGB 1 IN	BNC x 5
Terminals \| RGB 1 IN \| R, G, B	R: 0.7 Vp-p, 75 ohms, G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms, B: 0.7 Vp-p, 75 ohms HD, VD/SYNC: TTL, high impedance, positive/negative a utomatic NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Terminals \| RGB 1 IN \| Y, PB, PR (Y, CB, CR)	Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms
Terminals \| RGB 1 IN \| S-Video signal	Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms
Terminals \| RGB 2 IN	D-sub HD 15-pin (female) x 1
Terminals \| RGB 2 IN \| R, G, B	R: 0.7 Vp-p, 75 ohms, G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms, B: 0.7 Vp-p, 75 ohms HD, VD/SYNC: TTL, high impedance, positive/negative a utomatic NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Terminals \| RGB 2 IN \| Y, PB, PR (Y, CB, CR)	Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms
Terminals \| SERIAL IN	D-sub 9-pin (female) x 1 for external control (RS-232C compliant)
Terminals \| SERIAL OUT	D-sub 9-pin (male) x 1 for link control
Terminals \| Remoter 1 In	M3 jack x 1 for wired remote control
Terminals \| Remoter 1 Out	M3 jack x 1 for link control
Terminals \| Remoter 2 In	D-sub 9-pin (female) x 1 for external c ontrol (parallel)
Power cord length	3.0 m (9 ft 10 in)
Cabinet materials	Molded plastic
Dimensions (W x H x D)	620 x 291 x 800 mm (24-7/16 x 11-15/32 x 31-1/2 inches) (without lens)
Weight	Approx. 41 kg (90.4 lbs) (without lens)
Operating noise	46 dB (quad lamp operation)
Operating temperature	0°- 45°C (32°- 113°F)
Operating humidity	10%-80% (no condensation)
Technology	3-chip DLP